Mira Vie Guía de usuario

1These instructions are to be left with the userInstallation and User GuideELECTRIC SHOWERMIRA VIEMira Vie

10Plumbing1. Minimum maintained inlet pressure for satisfactory operation: 8.5 kW and 9.5 kW: 70 kPa (0.7 bar). 10.8 kW: 100 kPa (1.0 bar).2. Maxi

11Plumbing1. The Mira Vie 8.5 kW and 9.5 kW electric showers are designed to operate with a minimum maintained inlet pressure of 70 kPa (0.7 bar) up

1210. Do not install the appliance in a position where it may become frozen. The shower unit must not be tted where it may be exposed to freezing co

13Electrical1. This product is suitable for installation within Zone 1 and is rated IP X4.2. In a domestic installation, the rating of the electrici

14INSTALLATIONWarning! Isolate the electrical and water supplies before commencing installation. The electricity must be turned off at the mains and t

1510. The case has thinned sections that can be removed to allow entry of the supply pipe and electrical cables. Remove the top thinned section of th

1618. Bring the electrical cables into the case.19. Strip a short section of the electrical cables.20. Fit an earth sleeve to the earth wire.21. L

17COMMISSIONING1. Turn the shower OFF by pressing the power button. Make sure that the button is in the OFF position.2. Turn the temperature knob fu

18OPERATIONAdvice to UsersNote! Read the Important Safety Information section rst.DO NOT operate this appliance if water leaks from this appliance.Wa

19Operating InstructionsTo turn the shower on1. Switch on the electrical supply at the double pole switch. The light around the power button will tur

2CONTENTSIntroduction ...3Recommended Usage ...

20FAULT DIAGNOSISThe troubleshooting information tabled below gives you details on probable causes and remedies should difculties be encountered whil

21Malfunction Cause RemedyNo hot water from shower, with the knobs in any position.Other water outlets are being used during showering, causing the wa

22Malfunction Cause RemedyTurning the temperature knob does not affect the water temperature.The ow regulator is faulty. The handset sprayplate is bl

23Malfunction Cause RemedyWater leaks from the bottom of the case near the outlet, and there is no ow from the handset.The pressure relief valve in t

24MAINTENANCEAny maintenance must be carried out by a qualied tradesperson, following the instructions provided. Before replacing any parts

25Spare Parts List406.27 Filter439.74 Spare Neon Assembly439.75 Inlet Connector Assembly439.76 Clamp Bracket Pack (components identied ‘A’)439.78

26Spare Parts Diagram439.75406.271539.349439.801539.379439.78CCABAB439.97439.981539.4001539.4061539.440Important Note! Push-t connectors must be a

27ACCESSORIESEverclear ShowerheadWhite - 2.1616.030Chrome - 2.1616.0319.5 kW and 10.8 kW versions onlyMira's new Everclear range has been special

28CUSTOMER SERVICEMira is a registered trade mark of Kohler Mira Limited.The company reserves the right to alter product specifi cations without notice

3Thank you for purchasing a quality Mira Vie Electric Shower. To enjoy the full potential of your new shower, please take time to read this guide thor

4For domestic installations, Mira Showers guarantee the Mira Vie 8.5, 9.5 kW and 10.8kW against any defect in materials or workmanship for a period of

5Warning!1. Read all of these instructions and retain this guide for later use.2. Products manufactured by us are safe and risk-free, provided that

621. DO NOT commission this appliance if water leaks from the unit.22. DO NOT operate this appliance if water leaks from this appliance.23. Only a

7Caution!1. Read all of these instructions and retain this guide for later use.2. Make sure that this guide is left with the user. Pass on this guid

8 3 x Wall Plugs 3 x Fixing Screws 1 x Mira Vie Electric ShowerDocumentation 1 x Installation and User Guide 1 x Installation Template 1 x

9SPECIFICATIONSAll dimensions are nominal and in millimetres.Dimensions3721096318Wiring Diagram